Leader

Collapse

Announcement

Collapse
No announcement yet.

Brass to silver?

Collapse

300x250 Mobile

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Sandie23
    replied
    Thanks everyone. I actually found a shop here that will change them out. But thanks for all the input

    Leave a comment:


  • Shush
    replied
    Dude, if you are in the panhandle of Texas, there are probably leather shops on every corner. They can change them out for you in like 30 minutes, and super cheap. I had to go just the opposite with mine - silver to brass. Found a leather shop and they did all of mine in like 20 minutes and charged me like $10 total.

    You could probably get the tools and snaps to do it yourself from tandyleather.com. More expensive that way though. As for skill needed -- if you know how to use a stapler, you know how to put snaps on stuff.

    Leave a comment:


  • KenW.
    replied
    Most any upholstery shop can change the snaps.

    Leave a comment:


  • Seventy2002
    replied
    Originally posted by Resq14 View Post
    the obvious solution is to just replace them.
    Ditto that. Boating supply houses sell stainless steel snaps. Back before Velcro, we all started out with silver snaps. As you polished your gear the nickel plating wore off, exposing the brass underneath. Such equipment was described as "salty" or "nicely brassed" and wearing marked you as not a rookie.

    Leave a comment:


  • Monty Ealerman
    replied
    I agree with Resq14 regarding replacement being a much preferable option.

    Leave a comment:


  • Resq14
    replied
    Ignore the ridiculous post above. If you're going through the trouble of removing the snaps to electroplate, the obvious solution is to just replace them.

    I replaced snaps on my handcuff straps with special "one-way" snaps that only open from one direction. It's easy to do... just drill them out and use a special tool to install. Amazon and other stores sell snaps and the special tools to do it.
    http://www.amazon.com/Bestop-93001-5...+button+chrome

    Leave a comment:


  • Monty Ealerman
    replied
    electroplating:
    (comparatively difficult)
    http://www.amazon.co.uk/Nushine-Silv.../dp/B00D5TCYT8

    or

    paste silvering:
    (easier)
    10 gm silver chloride
    20 gm salt
    20 gm cream of tartar (potassium bitartrate)
    enough water to make a usable paste
    scrub the snaps with baking soda and a soft toothbrush and rinse them clean and dry them
    rub paste on cleaned snaps with a piece of leather or cork or a Q-tip
    lacquer them with clear nail polish afterward

    or

    stripping:
    (easiest)
    (not sure about Safariland snaps -- I think the brass finish is flashed onto nickel plating on the snaps with only the buckles on their leather goods being solid brass -- you can maybe check a worn area to tell)
    EZ-Off oven cleaner will take the brass plating off and expose the nickel plating below it
    use duct tape to isolate the snaps and protect the leather
    apply the EZ-Off with a handi-wipe or something rather than spraying it on directly
    http://www.stylenorth.ca/blog/2011/0...-oven-cleaner/
    then lacquer etc.
    Last edited by Monty Ealerman; 09-11-2014, 10:21 PM.

    Leave a comment:


  • mookster
    replied
    The sorcerers stone can do what you need...

    Leave a comment:


  • Sandie23
    started a topic Brass to silver?

    Brass to silver?

    Not sure if I'm putting this in the right place, but here goes.

    I am changing from my current SO to the local PD. SO required we have brass snaps, PD wants silver. Everything I have is Safariland leather with brass snaps. How can I change the snaps to silver? I am trying to avoid buying everything all over again.

MR300x250 Tablet

Collapse

What's Going On

Collapse

There are currently 2519 users online. 121 members and 2398 guests.

Most users ever online was 158,966 at 05:57 AM on 01-16-2021.

Welcome Ad

Collapse
Working...
X